Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
Schodowski_Info
Christine Florez From:Schodowski, Chris <CSchodowski@leviton.com> Sent:Friday, October 19, 2007 5:14 PM To:Brendan Reed; Alan.ridley@gcccd.edu; Alma Aguilar; Andrew McAllister; Brian Holland; brooke.lee@iclei.org; Carla Blackmar; Cesar Rios; Dawn Beintema; Denny Stone; Derek Turbide; epitts@ymca.org; Hector Reyes; LauraH@environmentalhealth.org; Leo Miras; Lynda Gilgun; Lynn France; Marisa Lundstedt; Michael Meacham; RBaron@semprautilities.com; Richard Chavez; Richard Hopkins; sfr@sandag.org; weprosper2@hotmail.com Cc:Kay Wright; Linda Wagner Subject:RE: CCWG Meeting #6 Attachments:SFX1570.pdf; BR_Leviton_Power.pdf; 3-Phase Power in the Data Center.pdf I’d like to share the attached information I came across at work this week as it relates to the Energy topic that we will be discussing next week. Leviton’s Power Solutions group (based in Chula Vista) is currently working with several large Data Centers across the country to implement intelligent PDU’s (Power Distribution Units). Intelligent PDU’s provide remote access via the internet to monitor and control the power to Data Center equipment. One of the many benefits is allowing IT departments to reduce energy consumption by remotely turning off idle equipment. The attached article from INDUSTRY WEEK discusses the enormous drain Data Centers are having on our electricity resources. It states that existing Data Centers consume enough electricity to power 5% of the homes in the US. In addition to intelligent PDU’s, we are seeing a growing trend in the Data Center industry to switch over to 3 Phase power operating at 208/240 V which is much more energy efficient. Attached is a White Paper from Server Tech which discusses this issue. On page 7 it discusses the GREEN DIRECTIVES – POWER EFFICIENCY GAINS. Mandating or encouraging more energy efficient data centers may be an opportunity for significant CO2 reductions seeing that almost every office has one. Chris Schodowski | Divisional Controller - Mexico& Import/Export | Corporate Finance Department Leviton Manufacturing Co., Inc. | 860 Harold Place, Chula Vista, CA 91914 619-205-8607 | 619-205-8685 | cschodowski@leviton.com From: Brendan Reed \[mailto:BReed@ci.chula-vista.ca.us\] Sent: Thursday, October 11, 2007 2:12 PM To: Alan.ridley@gcccd.edu; Alma Aguilar; Andrew McAllister; Brian Holland; brooke.lee@iclei.org; Carla Blackmar; Cesar Rios; Schodowski, Chris; Dawn Beintema; DStone@ci.chula-vista.ca.us; Derek Turbide; epitts@ymca.org; Hector Reyes; LauraH@environmentalhealth.org; Leo Miras; Lynda Gilgun; Lynn France; mlundstedt@ci.chula-vista.ca.us; Michael Meacham; RBaron@semprautilities.com; Richard Chavez; RAHopkins@ci.chula-vista.ca.us; sfr@sandag.org; weprosper2@hotmail.com Cc: Kay Wright; Linda Wagner Subject: CCWG Meeting #6 Hey folks: Thank you for a very productive meeting yesterday and thank you to Richard Chavez who volunteered to be the Working th Group’s new Chair. Attached are the materials for our next CCWG meeting on October 24 from 3-5pm at the Public Works Corp Yard (Conf Room C): th October 10 Meeting Summary th October 24 Meeting Agenda 1 Measures Evaluation – “Energy” Also, staff is working to place a “Carbon Footprint” calculator on the City’s website, but we need your help in selecting the best one! If you have a free moment, please try the following on-line calculators and let us know which one is your favorite: http://www.epa.gov/climatechange/emissions/ind_calculator.html http://www.climatecrisis.net/takeaction/carboncalculator/ http://www.nature.org/initiatives/climatechange/calculator/ Thanks, B- Brendan Reed, LEED-AP City of Chula Vista Environmental Resource Manager Dept. of Conservation & Environmental Services 619-409-5889 Office 619-549-5690 Cell 2 DATA CENTER POWER SOLUTIONS LEVITON’S INTELLIGENT POWER DISTRIBUTION UNITS Your critical applications and equipment are only as good as the power that drives them. In Data Centers and other “always on” environments, Leviton’s Intelligent Power Distribution Units (PDU’s) provide robust power distribution and advanced local and remote power monitoring and management. PDU’s, an important part of Leviton’s e2x Architecture for Data Centers, are the ideal solution when reliability and manageability are especially critical. Leviton offers both Metered and Switched (remote managed) models in multiple confi gurations to fi t a variety of application environments: • Vertical Zero-U or horizontal rack-mount styles • 110-120V or 208-240V and 20 and 30 amps • Various input and output plug styles Power Leviton | Phone 800.722.2082 | www.levitonvoicedata.com POWER DISTRIBUTION FOR “ALWAYS ON” ENVIRONMENTS Leviton PDU’s can help you to: • Monitor input current and determine if you have enough power to plug in another device • Appropriately size power infrastructure for future projects • Reboot servers and other network devices remotely • Sequence power during start-up to avoid power in-rush • Manage grouped or individual outlets • Monitor temperature and relative humidity in data center cabinets • Receive SNMP alerts when power or environmental conditions exceed thresholds • Accommodate diverse power options complete ordering information available on inside back cover Phone 800.722.2082 | Fax 425.483.5270 | www.levitonvoicedata.com 3 PDPPUDDDUDDIntelligent Power Distribution Units Leviton’s Metered Power Distribution Units provide the reliable power distribution required for high-demand applications. Industrial-grade outlets and IDC-based conductor terminations enhance reliability and ease of use. Local LED display provides input current monitoring, giving on-site users the ability to monitor aggregate current drawn as equipment is connected to each unit. Input Current Monitoring - Leviton’s True RMS Current Monitoring helps to prevent overloads in high-density computing environ- ments, by telling users whether they have suffi cient power to plug in another device. With "True RMS” you’ll always receive the most accurate current reading possible for appropriate power allocation. The 3-phase metered unit includes one LED display for each phase. Branch Circuit Protection - Leviton’s Intelligent PDU offering meets the UL 60950-1 requirement for branch circuit protection. Over- current protection is provided for each branch circuit via UL-listed Bussman SC fuses. In the event of an overload, only one branch circuit is affected, allowing the other branch to continue functioning normally. Vertical “Zero-U” PDU’s feature quick-access fuse panels for easy replacement. Mounting Hardware - Both Metered and Switched PDU’s come with a versatile mounting bracket that allows attachment and positioning within most cabinets and racks. Also included is a button-mounting feature increasingly used by cabinet manufacturers for simplifi ed installation. Power Options to Fit Every Application - Leviton offers reliable 110-120V or 208-240V power distribution with 20 and 30-Amp options. A hardwired power input is provided with all 30-Amp PDU’s. Power cords for 20-Amp PDU’s are available separately. [ Power Cables ] [ Button-Mounting ] [ Branch Circuit ] [ Input Current Monitoring ] METERED PDU'S POWER DISTRIBUTION UNITS 4 Phone 800.722.2082 | Fax 425.483.5270 | www.levitonvoicedata.com complete ordering information available on inside back cover PDPPUDDDUDDIntelligent Power Distribution Units SWITCHED PDU'S POWER DISTRIBUTION UNITS Leviton’s Switched Power Distribution Units include all the features of Metered PDU’s, plus the additional functions detailed below, to provide enhanced intelligence for monitoring and control of data center power outlets. These capabilities address many IT power management problems including unauthorized use of power outlets, equipment lock-up, in-rush current, overloaded circuits and remote access to power outlets. Remote Management & Reboot - As simple as point and click, Leviton’s Switched PDU allows you to remotely reboot a locked-up device, providing complete confi guration and control of the remote unit via the HTML interface. HTTPS-enabled Ethernet connections and a command line interface for serial and Telnet connections provide immediate access for simultaneous multiple users managing multiple locations. Power Up Sequencing - The power sequence feature controls the interval in which equipment is powered up or down to avoid cumulative in-rush current. Unlike many “similar” PDU’s, sequencing applies to both initial power-up and user-commanded actions, and in the event of recovery, defaults to the most recent confi guration. Network Input Current Monitoring - Input Current Monitoring with IP access eliminates the guesswork of determining available power draw on circuits. This helps ensure appropriate equipment confi guration and device density to make full use of capacity, while also assisting in planning and appropriately sizing future power circuit requirements. SNMP-based alerts indicate excess power draws. Environmental Monitoring - Two external probes (sold sepa- rately) protect your IT and network hardware with cabinet-level environmental monitoring. SNMP-based alarms alert you when temperature and relative humidity vary from defi ned conditions. [ Environmental Monitoring ] [ Network Input Current Monitoring ] [ Remote Management ] [ Power Up Sequencing ] complete ordering information available on inside back cover Canada 800.405.5320 | Int’l 425.486.2222 | www.levitonvoicedata.com 5 Accessible from a standard HTML web browser, the interface is constructed of three major components: The Control Screen is used to display current data and allow changes to outlet states or system confi guration. Switched PDU Web Interface The System Location Bar displays the location and IP address as well as the current Control Screen title. The User/Navigation Bar displays the current user and privilege level per assigned access rights. The Switched PDU Web Interface provides remote confi guration, monitoring and control of the unit, allowing customized access for individual users. All Switched PDU models support multi-user simultaneous session communication methods including HTTPS, HTTP, Telnet or SSHv2, SNMP-II, and single serial RS232 console access, making them ideal for co-location sites. Remote on, off, and reboot functions can be assigned to individual outlets, groups of outlets, or all outlets. Individual accounts may be limited in a variety of ways. Access may be restricted to a single user or extended to up to 120 users. 2 1 3 3INGLE 5SER -ULTI 5SERS -ULTI ,OCATIONS INPUT CURRENT T/H 1 Ser Net T/H 2 1 2 6 Phone 800.722.2082 | Fax 425.483.5270 | www.levitonvoicedata.com METERED VERTICAL POWER DISTRIBUTION UNITS (PDU'S) DIMENSIONS POWER INPUTS POWER OUPUTS INPUT VOLTAGE 1 OR 3 PHASE AMPERAGE INPUT PLUG TYPE OUTPUT RECEPTACLE PART NO. 31.25" X 1.75" X 2.25" 1 12 110 1 20 C20 5-20R MV121-1D1 31.25" X 1.75" X 2.25" 1 12 110 1 30* L5-30 5-20R MV121-1B1 31.25" X 1.75" X 2.25" 1 12 208 1 30* L6-30 C13 MV122-1C2 54.0" X 1.75" X 2.25" 1 24 110 1 20 C20 5-20R MV241-1D1 54.0" X 1.75" X 2.25" 1 24 110 1 30* L5-30 5-20R MV241-1B1 54.0" X 1.75" X 2.25" 1 24 208 1 30* L6-30 C13 MV242-1C2 45.75" X 1.75" X 2.25" 1 21 208 3 20 L21-20 C13 MV213-1E2 5-20P 120V 20A L6-30P 230V 30AL5-30P 120V 30AC13 120/230V 10A5-20R 120V 15AC19 120/230V 20A 16A - Europe * All 30 amp PDU's include a hardwired power input cord Other confi gurations available on request. METERED HORIZONTAL POWER DISTRIBUTION UNITS (PDU'S) DIMENSIONS POWER INPUTS POWER OUPUTS INPUT VOLTAGE 1 OR 3 PHASE AMPERAGE INPUT PLUG TYPE OUTPUT RECEPTACLE PART NO. 1.75" X 17.25" X 5" 1 10 110 1 20 C20 5-20R MH101-1D1 1.75" X 17.25" X 5" 1 10 110 1 30* L5-30 5-20R MH101-1B1 1.75" X 17.25" X 5" 1 12 208 1 30* L6-30 C13 MH122-1C2 ACCESSORIES DESCRIPTION PART NO. Power Cord, 15/20A, C19 to L-620P, 10 ft. PCORD-F10 Power Cord, 15/20A, C19 to 5-15P, 10 ft. PCORD-G10 Power Cord, 15/20A, C19 to 5-20P, 10 ft. PCORD-A10 Power Cord, 15/20A, C19 to L5-20P, 10 ft. PCORD-H10 5-15P 120V 15A L5-20P 120V 20AL6-20P 230V 20AC20 120/130V 20A L21-20P 208V 30A [ MH101-1*1 ] [ MH122-1C2 ][ MV122-1C2 ] [ MV213-1E2 ] [ MV242-1C2 ][ MV241-1*1 ][ MV121-1*1 ] PDPPUDDDUDDIntelligent Power Distribution Units Canada 800.405.5320 | Int’l 425.486.2222 | www.levitonvoicedata.com 7 * All 30 amp PDU's include a hardwired power input cord Other confi gurations available on request SWITCHED VERTICAL POWER DISTRIBUTION UNITS (PDU'S) DIMENSIONS POWER INPUTS POWER OUPUTS INPUT VOLTAGE 1 OR 3 PHASE AMPERAGE INPUT PLUG TYPE OUTPUT PLUG TYPE PART NO. 63.5" X 1.75" X 2.25" 1 16 110 1 20 C20 5-20R SV161-1D1 63.5" X 1.75" X 2.25" 1 16 110 1 30* L5-30 5-20R SV161-1B1 63.5" X 1.75" X 2.25" 1 16 208 1 30* L6-30 C13 SV162-1C2 SWITCHED HORIZONTAL POWER DISTRIBUTION UNITS (PDU'S) DIMENSIONS POWER INPUTS POWER OUPUTS INPUT VOLTAGE 1 OR 3 PHASE AMPERAGE INPUT PLUG TYPE OUTPUT PLUG TYPE PART NO. 1.75" X 17" X 7" 1 8 110 1 20 C20 5-20R SH081-1D1 1.75" X 17" X 7" 1 8 208 1 30* L6-30 C13 SH082-1C2 1.75" X 17" X 7" 1 8 110 1 30* L5-30 5-20R SH081-1B1 ACCESSORIES DESCRIPTION PART NO. Power Cord, 15/20A, C19 to L-620P, 10 ft. PCORD-F10 Power Cord, 15/20A, C19 to 5-15P, 10 ft. PCORD-G10 Power Cord, 15/20A, C19 to 5-20P, 10 ft. PCORD-A10 Power Cord, 15/20A, C19 to L5-20P, 10 ft. PCORD-H10 Temperature & Relative Humidity Probe, 10 ft. TCORD-10 5-20P 120V 20A L6-30P 230V 30AL5-30P 120V 30AC13 120/230V 10A5-20R 120V 15AC19 120/230V 20A 16A - Europe 5-15P 120V 15A L5-20P 120V 20AL6-20P 230V 20AC20 120/130V 20A L21-20P 208V 30A [ SH081-1*1 ] [ SH082-1C2 ] [ SV161-1*1 ] [ SV162-1C2 ] J/5-#1469 Customer Service 800.722.2082 | Int’l 425.486.2222 | Literature Requests 800.922.6229 | www.levitonvoicedata.com WE KNOW POWER MANAGEMENT EXCELLENCE IS CRITICAL TO YOU. THAT’S WHY WE DO EVERYTHING WE CAN TO BE SURE OUR PRODUCTS AND SERVICES WILL MEET AND EXCEED YOUR EVERY NEED. COMPLETE CUSTOMER SERVICE | We believe service comes in many forms. With expert technical support, detailed product information, and a dedicated customer service team, we help our customers truly understand how and when to use our products in today’s changing technology environment. CONSISTENT QUALITY | We have a commitment to continuous improvement. To achieve that goal, our manufacturing and engineering functions are consistently monitored and perfected through the use of quality assurance tools such as Six Sigma quality improvement and compliance with ISO 9001-2000. POWER QUALITY TEST FACILITY | We want to know our products will work for you every time in every installation. So we test all of our products in our lab, a rigorous environment designed to emulate real-world installations. If our products perform there for us, they’ll perform anywhere for you. LEVITON WARRANTIES | Leviton produces the highest quality products available and backs them with one of the strongest warranties in the industry. Server Technology, Inc. 3-Phase Power in the Data Center White Paper STI-100-005 North America/ASIA EMEA Server Technology, Inc. Server Technology Intl. 1040 Sandhill Drive Sienna Court Reno, NV 89521 The Broadway United States Maidenhead +1 (775) 284-2000 Berkshire SL6 1NJ sales@servertech.com United Kingdom www.servertech.com +44.1628.509053 Tel www.servertechblog.com salesint@servertech.com 3-Phase Power in the Data Center INTRODUCTION High density computing with increased server implementation, greater equipment densities, increased power demands, cost reduction initiatives, green directives and redundancy are driving the demand for 3-Phase power in the data center equipment cabinet. Several years ago just talking about 3-Phase power distribution at the equipment cabinet would have brought laughs and looks of amazement from your fellow data center employees. Today, there are several simple facts within the data center environment that have created demand for 3-Phase power in the equipment cabinet. 1) IT equipment comes standard with universal power supplies that take a wide range of input power and most commonly can support 208 V/230 V power. 2) 208 V power is more efficient than 120 V power and with the high cost of power today every little bit helps. 3) The amount of power that a 3-Phase power whip can deliver, whether it is 20, 30 or 60 Amp, is almost twice the power or (1.73 times) more than a single phase whip can. 4) Cost savings: Lower number of power whips required at the cabinet, less cables at the bottom of the cabinet or under the floor to block air flow, less poles taken up at the power distribution panel, lower number of cabinet power distribution units needed in the cabinet, greater power efficiencies, and less rework required as the data center expands or new equipment is brought in. 5) The ability with 3-Phase Wye power to distribute both 208 V and 120 V power from the same cabinet power distribution unit. 6) 3-Phase power provides for redundancy and future expansion. This paper will explore the 3-Phase power, how it works, why it is more efficient and many other advantages it provides to the data center. 2Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com. 3-PHASE POWER 3-Phase power often denoted as 3Φ is the most efficient way to produce and distribute electricity. Nearly all power in the world today is generated as 3- Phase. 3-Phase power combines three electric circuits into one and is supplied over three wires which are typically labeled X, Y and Z in the United States US and L1, L2 and L3 in the European Union EU. The line voltages between the three possible pairs of wires are XY, YZ and XZ or in Figure 1 are listed as Phases 1, 2 and 3. For industrial applications 3-Phase power is more constant over time making it better suited than single phase power for applications like large industrial loads. This is due to the fact that when a single phase is crossing through zero the two remaining phases are non- zero, either positive or negative, ensuring that the load has a more constant source of power. Each phase is offset from the other by 120 degrees or a 1/3 of a cycle as shown in Figure 1. Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com 3 Figure 1 3-Phase power is delivered in either a Delta or Wye configuration source. A delta configuration consists of 3 line wires and one ground wire (see Figure 2). Looking at the wiring diagram it is obvious why it is called a delta configuration as it resembles the Greek letter of the same name ∆. A 3- Phase delta configuration, supplies three 208 V single phase power outputs to power IT equipment via Vxy, Vyz and Vxz. . Three-Phase Delta: Y Z X Figure 2 Figure 3 3-Phase Wye power consists of 3 line wires, a common neutral wire, and one ground wire (see Figure 4). Again looking at the wiring diagram it is obvious why it is called a Wye as it is shaped like a “Y”. Due to the one additional neutral wire, 3-Phase Wye configurations can supply both 120V and 208 V single phase outputs. 120 V is supplied to a load by connecting the common neutral wire to any one of the three lines X, Y and Z. 208 V is derived by connecting a load to any two of the 120 V lines XY, YZ, XZ and because of this it is often called dual phase power. 208 V is supplied from the two 120 V line voltages as (120 V x 1.73) = 208 V not 240 V or (120 V + 120 V)= 240 V as might be expected. This is a result of each phase being just 1/3 a cycle offset in time (see Figures 3 and 5). The voltage does not fully double because no two lines are ever at peak forward or reverse voltage at the same time. Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com 4 Three-Phase Wye: X Y Z Figure 4 Figure 5 . Let’s now explore the total power available that a 3-Phase system can deliver to the devices in the cabinet. As an example let’s take a look at a common 208 V 3-Phase 30A power whip going to a cabinet. Power is the rate of doing work and is calculated as P = V (volts) x I (Amps) or VA or Watts in a single phase system. For a 3-Phase system P =V x I x 1.732 is used to determine VA or Watts. Most people might infer that this whip would deliver 90 amps of current (3 (for three phases) x 30 A) but it actually delivers 30 A X 1.732 or 51.96 amps of current to the load. The total kW’s delivered on a 3-Phase 208 V 30A power whip is calculated as 208 V x 30A x 1.732 or 10.8 kW of power versus a standard 208 V 30 A whip which only delivers 6.2 kW of power. So the 3-Phase system delivers almost twice or 1.732 times the amount of power that a single phase system delivers. Power Calculations (not de-rated) Single Phase Power Power(P)=V x I =208V x 30A = 6.2 kW 3-Phase Power Power(P)=V x I x 1.732=208V x 30A x 1.732 = 10.8 kW Where P = Power in VA or Watts, V=Volts, I=Amps and 1,000 VA= 1 kVA or 1 kW Note: All calculations assume a power factor of 1 (p.f.=1) Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com 5 Where do we get the magic number of 1.732 or the square root of 3 from? Each phase in a 3-Phase system is separated from each other of the other 2 phases by 120 degrees. Vector math can be used to determine the voltages between any of the two lines as follows: X, Y AND Z ARE THE PHASE VOLTAGES VXY, VYZ AND VXZ ARE LINE VOLTAGES X X Y Z X Y Z 120 VAC 120 VAC 1200 120 VAC Figure 6 1200 1200 Table 1 . Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com 6 VXY=2 X (120 VAC X COS (30)) OR (120 VAC)(2 X COS (30)) OR 120 VAC X 1.732 = 208 VAC WHERE 2 X COS (30) = 1.732 OR THE SQUARE ROOT OF THREE (√3) LOAD BALANCING Power calculations for 3-Phase systems become significantly more complicated when the load is “out of balance” or “unbalanced”. Three phase loads are defined as being out of balance when the load current between any two lines X, Y, or Z is significantly different than the load current between the remaining line. Example: Ixy= 15 A, Iyz= 15 A and Ixz= 0 A. When a load is out of balance, in a Wye configuration, current will flow through the neutral connection causing heating which affects the overall efficiency of the system and the overall amount of power being delivered. Some Cabinet Power Distribution Unit (CDU) suppliers provide three local current load meters (one for each phase) on the CDU to help make load balancing a simple and easy process by instantly knowing what the line current is for the devices being installed in the cabinet. It is much easier to use a device that measures the actual line current than having someone try to perform these calculations. OTHER FACTORS TO CONSIDER WHEN CALCUATING POWER (DE-RATING) When doing power calculations the user should not expect to utilize the full current or power rating that the whip is providing to the cabinet as a safety or de-rating factor needs to be applied. The NEC (National Electric Code) specifies a 20% or x .8 de-rating factor is applied to rack mounted CDU’s. This is a very reasonable and practical factor to be used. The power calculations used in Table 3 have a .8 safety factor applied. Depending on the facility and the specific constraints some IT Managers will apply either a lower or higher factor. X 12 0 120 VAC VX Vy120o Y 30o 30o VXY Figure 7 . UNIVERSAL POWER SUPPLIES - IT EQUIPMENT AND CABLE MANAGEMENT Virtually all IT equipment today comes standard with a universal power supply. These power supplies vary but looking at the one at my desk for my DELL laptop computer shows an input of 100 to 240 volts at 50 - 60 Hz. The confusion as to what power can be connected to it seems to lie with the power cord. In most cases IT equipment shows up with a NEMA 5-15 P plug on it leading the user to believe that they have purchased a 120 V device when in reality it can be just as easily be powered with 208 V or 230 V power (see Figure 8). (Note: Each device should be reviewed to verify 100 V to 240 V compatibility before power is applied.) In these cases the standard power cords delivered with the equipment should not be used and swapped with a cord that has a IEC C13/C19 on one end to plug into the IT device and either IEC C14 or C20 on the other for plugging into the Cabinet Power Distribution Unit (CDU) (see Figure 9). Along with purchasing cables that allow your devices to be 208 – 230 V powered there is the extra advantage of being able to order cables in the proper lengths. This avoids cable management problems, giving the equipment cabinet a cleaner look and making it much easier to install new equipment or service the existing equipment along with not interfering with airflow. Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com 7 Standard Power Cord – Exchanged for new power cord New Power Cord – Allows connection to 208/230 V power sources Figure 8 Figure 9 GREEN DIRECTIVES – POWER EFFICIENCY GAINS Organizations committed to reducing their carbon footprint in their data centers are doing power/energy assessments and are finding many ways to save large amounts of power. Some of the more common ways to save energy in the data center are: 1) Improving cooling efficiency using best practices 2) Virtualization . 3) Turn-off idle IT equipment 4) Consolidation 5) Enable CPU power management feature on IT equipment 6) Purchase IT equipment with high efficiency power supplies 7) Use high efficiency UPS’s 8) Adopt power distribution at 208/230 V There is a simple way to increase the efficiency in your data center by a few percentage points. As there is a 2% efficiency gain just by going from to 120 V to 208 V power and a 3% efficiency gain going from 120 V to 230 V power with many devices. To determine what the gain is on your servers and other devices review the power supply specification and look at the efficiency % based on the various input voltages. The example below is taken from a HP power supply specification sheet for their ProLiant® DL380 server (see Table 2). Power Supply Specification HP ProLiant DL380 Generation 5 (G5) Operational Input Voltage Range (Vrms) 90 to 264 Nominal Input Voltage (Vrms) 120 208 230 Efficiency % 82 84 85 Table 2 HIGH DENSITY POWER - AMOUNT OF POWER DELIVERED Increased cabinet densities, blade servers and other high density installations now require more power is brought to the cabinet level. The amount of power required is a function of the equipment installed in the cabinet, whether redundancy is required and if the data center is planning for future expansion or additional equipment to be installed in the cabinet. The average kW per cabinet in the typical data center has jumped from 3-4 kW’s to 6-8 kW’s per cabinet depending on the industry and the application. This is a trend that is likely to continue with future predictions as high as 33 kW per cabinet on average by 2011 as reported by the Gartner group. Table 3 shows the amount of power in kW’s being delivered, depending on the different power drops available today. 8Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com. Circuit Power Drop Comparison C Power Drop Delivered Power in kW (derated) # of Branch Circuits # of Poles Branch Circuit Protection 120 V Support 208 V Support 120 V 15 A 1.44 1 1 N Y N 120 V 20 A 1.92 1 1 N Y N 120 V 30 A 2.88 2 1 Y Y N 208 V 20 A 3.33 1 2 N N Y 208 V 30 A 4.99 2 2 Y N Y 208 V 3- Phase 30 A 8.64 3 3 Y Y (Wye) Y 208 V 3- Phase 60 A 17.28 6 3 Y Y (Wye) Y Table 3 Looking at the table above it becomes clear that today’s increased densities require new power solutions at the cabinet level. For example, why run just 208 V 20A power, which provides 3.33 kW a drop when you can run 208 V 30 A power and get 4.99 kW per drop to the cabinet at roughly the same cost. It also becomes clear that with the average kW densities running in the 6-8 kW range that in many installations including redundancy 208 V 30 A 3-Phase power is required to cost effectively meet today’s high density requirements. When working with a PDU supplier make sure they have a complete product offering that includes 16A, 20A, 30A, 32A, 60A current capabilities along with 120 V, 208 V, 208 V 3-Phase and 400 V 3-Phase product solutions. Also, make sure that key operating features are available such as local and remote current monitoring, environmental monitoring, SNMP traps, email alerts, secure web based GUI, out of band serial connection, and the ability to remotely reboot locked up servers and network devices. 9Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com. INSTALLATION EXAMPLE A simple installation example is a good way to illustrate how many power whips are required, including redundancy, to operate ten (10) HP Model DL- 380-GL servers requiring 7.4 kW of power. Server Cabinet Server 1 HP DL-380-G5 1000 W Server 2 HP DL-380-G5 1000 W Server 3 HP DL-380-G5 1000 W Server 4 HP DL-380-G5 1000 W Server 5 HP DL-380-G5 1000 W Server 6 HP DL-380-G5 1000 W Server 7 HP DL-380-G5 1000 W Server 8 HP DL-380-G5 1000 W Server 9 HP DL-380-G5 1000 W Server 10 HP DL-380-G5 1000 W Upon start up 10,000 W Consumed 7,425 W Installation Example: Server Cabinet with 7.4 kW power demand Solution/Wiring Configuration: Solution 1: (3) 120 V, 30 A circuits (8.6 kW delivered de-rated) (6) circuits required for redundancy Solution 2: (2) 208 V, 30 A circuits (9.98 kW delivered de-rated) (4) circuits required for redundancy Solution 3: (1) 208 V 3-Phase, 30 A circuit (8.6 kW delivered de-rated) (2) circuits required for redundancy Table 4 Outlet sequencing, within the CDU, is used to handle the increased power demands due to in-rush currents during startup. It is clear from this installation example that by providing higher density power to the cabinet and more specifically 3-Phase power that the number of drops run to the cabinet is greatly reduced resulting in significant cost savings throughout the data center. 10Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com. COST SAVINGS AND OTHER ADVANTAGES TO 3-PHASE POWER There is a definite cost associated with each power whip that is run to a cabinet. Estimates vary depending on who is doing the work and the location but on average it cost between $750 and $1,000 per whip. So by running 3-phase power there is a definite cost savings associated with running a lower number of whips versus a higher number. With fewer whips delivering more power there is a secondary, inherent savings from lower infrastructure costs by using less poles at the PDU or the power distribution panel (see Table 3). With a lower number of cables under the floor and in the bottom of the cabinet there are fewer objects to block the air flow within the raised floor. An optimized installation makes for a cleaner work environment and less confusion and problems during installation and maintenance. Along with reducing the number of cables being run with three phase power, is the added advantage of requiring fewer Cabinet Power Distribution Units within the cabinet. This provides additional cabinet space for other devices along with eliminating equipment which again blocks airflow. The concept of 0 U CDU’s that are mounted in the back of cabinets are now giving way to Modular 3-Phase CDU’s that can be mounted in the sides of cabinets. In some installations today even the back of the cabinet does not have enough room to support multiple CDU’s. By running 208 V or 230 V power there are cost savings due to efficiency gains instead of running 120 V within the cabinet. In many case these gains are 2-3 % or greater depending on the device and the efficiencies of its power supply at higher input voltages. This information is readily available for most IT equipment through the manufacturer. The average refresh rate of IT equipment, is every 3-5 years. Considering the increased power demand and the fact that this trend is very likely to continue, it makes sense to plan for future power demands. First, consider changing all equipment over to 208 V power. Next plan for near term infrastructure needs with 208 V single phase power and possible current or future requirements such as 208 V/400 V three-phase power. High availability, high demand, 7 x 24 Tier III and Tier IV data centers continue to become more common with redundant power sources (A and B power drops) within the cabinet. When redundant power is required the amount of power required within the cabinet doubles. These higher densities in many cases require the user to go to 3-Phase power to meet this increased demand. 11Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com. WHAT DOES THE FUTURE HOLD? Various arguments are being made for DC power in the data center as well as moving to 230V single phase and 400 V 3-Phase power in North America like much of the rest of the world to help meet the increased power demands within the data center. It is clear that increased power demands and greater equipment densities are here to stay for the foreseeable future. The Server Technology White Paper Blade Server Power Solutions: Cabinet Level Power Distribution Solutions for High Density Cabinets STI-100-001 discusses the current power demand trends within the data center. CONCLUSION For new data centers, equipment refresh and renovations 3-Phase power should be considered as the primary power choice. The advantages and cost savings are clearly there, while the disadvantages or risks are minimal. With the few remaining 120 V powered devices in the facility, 3-Phase power still has the ability to support them. For some IT Managers the choice of going with 3-Phase power is being made for them as increased power demands and redundancy have forced the issue within their facility along with cost analysis information showing the increased savings versus single phase power. If your IT equipment is located in a Co-Location facility or an older data center that is running out of power you may not have the choice to run 3-Phase power but it should always be considered as an option. With definite cost and efficiency advantages as shown in this paper 3-Phase power is becoming the power option of choice today for many data centers. In some locations, this is now being seen as more of a requirement than as an option as densities continue to increase. 12Server Technology, Inc. ©2007Server Technology Inc. 3-Phase Power in the Data Center 8/21/2007 All right reserved. No part of this publications may be used without written permission of the copyright owner www.servertech.com.